Tag Archives: sensitivity

Color, Formats, IQ, Sensors

Phase One IQ3 100MP Trichromatic vs Standard Back Linear Color, Part I

2 Comments

It is always interesting when innovative companies push the envelope of the state-of-the-art of a single component in their systems because a lot can be learned from before and after comparisons.   I was therefore excited when Phase One introduced a Trichromatic version of their Medium Format IQ3 100MP Digital Back last September because it could allows us to isolate the effects of tweaks to their Bayer Color Filter Array, assuming all else stays the same.

Figure 1. IQ3 100MP Trichromatic (left) vs the rest (right), from PhaseOne.com.   Units are not specified but one would assume that the vertical axis is relative spectral sensitivity and the horizontal axis represents wavelength.

Thanks to two virtually identical captures by David Chew at getDPI, and Erik Kaffehr’s intelligent questions at DPR, in the following articles I will explore the effect on linear color of the new Trichromatic CFA (TC) vs the old one on the Standard Back (SB).  In the process we will discover that – within the limits of my tests, procedures and understanding[1] – the Standard Back produces apparently more ‘accurate’ color while the Trichromatic produces better looking matrices, potentially resulting in ‘purer’ signals. Continue reading Phase One IQ3 100MP Trichromatic vs Standard Back Linear Color, Part I →

IQ, Sensors

Determining Sensor IQ Metrics: RN, FWC, PRNU, DR, gain – 2

2 Comments

There are several ways to extract Sensor IQ metrics like read noise, Full Well Count, PRNU, Dynamic Range and others from mean and standard deviation statistics obtained from a uniform patch in a camera’s raw file.  In the last post we saw how to do it by using such parameters to make observed data match the measured SNR curve.  In this one we will achieve the same objective by fitting mean and  standard deviation data.  Since the measured data is identical, if the fit is good so should be the results.

Sensor Metrics from Measured Mean and Standard Deviation in DN

Continue reading Determining Sensor IQ Metrics: RN, FWC, PRNU, DR, gain – 2 →

IQ, Sensors

Determining Sensor IQ Metrics: RN, FWC, PRNU, DR, gain – 1

Leave a comment

We’ve seen how to model sensors and how to collect signal and noise statistics from the raw data of our digital cameras.  In this post I am going to pull both things together allowing us to estimate sensor IQ metrics: input-referred read noise, clipping/saturation/Full Well Count, Dynamic Range, Pixel Response Non-Uniformities and gain/sensitivity.

There are several ways to extract these metrics from signal and noise data obtained from a camera’s raw file.  I will show two related ones: via SNR in this post and via total noise N in the next.  The procedure is similar and the results are identical.

Continue reading Determining Sensor IQ Metrics: RN, FWC, PRNU, DR, gain – 1 →

IQ, Sensors

Sensor IQ’s Simple Model

Leave a comment

Imperfections in an imaging system’s capture process manifest themselves in the form of deviations from the expected signal.  We call these imperfections ‘noise’ because they introduce grain and artifacts in our images.   The fewer the imperfections, the lower the noise, the higher the image quality.

However, because the Human Visual System is adaptive within its working range, it’s not the absolute amount of noise that matters to perceived Image Quality (IQ) as much as the amount of noise relative to the signal – represented for instance by the Signal to Noise Ratio (SNR). That’s why to characterize the performance of a sensor in addition to signal and noise we also need to determine its sensitivity and the maximum signal it can detect.

In this series of articles I will describe how to use the Photon Transfer method and a spreadsheet to determine basic IQ performance metrics of a digital camera sensor.  It is pretty easy if we keep in mind the simple model of how light information is converted into raw data by digital cameras:

Sensor photons to DN A
Figure 1.

Continue reading Sensor IQ’s Simple Model →

Equivalence, Exposure, IQ, Sensors

Equivalence and Equivalent Image Quality: Signal

1 Comment

One of the fairest ways to compare the performance of two cameras of different physical characteristics and specifications is to ask a simple question: which photograph would look better if the cameras were set up side by side, captured identical scene content and their output were then displayed and viewed at the same size?

Achieving this set up and answering the question is anything but intuitive because many of the variables involved, like depth of field and sensor size, are not those we are used to dealing with when taking photographs.  In this post I would like to attack this problem by first estimating the output signal of different cameras when set up to capture Equivalent images.

It’s a bit long so I will give you the punch line first:  digital cameras of the same generation set up equivalently will typically generate more or less the same signal in e^- independently of format.  Ignoring noise, lenses and aspect ratio for a moment and assuming the same camera gain and number of pixels, they will produce identical raw files. Continue reading Equivalence and Equivalent Image Quality: Signal →